1045 steel heat treated properties

Lab Report

EXPERIMENT 6

HEAT TREATMENT OF STEEL

Purpose

The purposes of this experiment are to:

 Investigate the processes of heat treating of steel  Study hardness testing and its limits  Examine microstructures of steel in relation to hardness

Background

To understand heat treatment of steels requires an ability to understand the Fe-C phase

diagram shown in Figure 6-1. Steel with a 0.78 wt% C is said to be a eutectoid steel. Steel

with carbon content less than 0.78 wt% C is hypoeutectoid and greater than 0.78 wt% C is

hypereutectoid. The region marked austenite is face-centered-cubic (FCC) and ferrite is

body-centered-cubic (BCC).

There are also regions that have two phases. If one cools a hypoeutectoid steel from a point in

the austenite region, reaching the A3 line, ferrite will form from the austenite. This ferrite is

called proeutectoid ferrite. When A1 is reached, a mixture of ferrite and iron carbide

(cementite) forms from the remaining austenite. The microstructure of a hypoeutectoid steel

upon cooling would contain proeutectoid ferrite plus pearlite (+ Fe3C).

The size, type and distribution of phases present can be altered by not waiting for

thermodynamic equilibrium. Steels are often cooled so rapidly that metastable phases appear.

One such phase is martensite, which is a body-centered tetragonal (BCT) phase and forms

only by very rapid cooling.

Much of the information on non-equilibrium distribution, size and type of phases has come

from experiments. The results are presented in a time-temperature-transformation (TTT)

diagram shown in Figure 6-2. As a sample is cooled, the temperature will decrease as shown

in curve #1. At point A, pearlite (a mixture of ferrite and cementite) will start to form from

austenite. At the time and temperature associated with point B, the austenite will have

completely transformed to pearlite. There are many possible paths through the pearlite

regions. Slower cooling causes coarse Pearlite, while fast cooling causes fine pearlite to form.

Cooling can produce other phases. If a specimen were cooled at a rate corresponding to curve

#2 in Figure 6-3, martensite, instead of Pearlite, would begin to form at Ms temperature (point

C), and the pearlite would be completely transformed to martensite at temperature Ms.

Martensite causes increased hardness in steels.

Unfortunately, hardness in steels also produces brittleness. The brittleness is usually

associated with low impact energy and low toughness. To restore some of the toughness and

impact properties it is frequently necessary to "temper" or "draw" the steels. This is

accomplished by heating the steel to a temperature between 500ºF (260ºC) and 1000ºF (540ºC).

Tempering removes some of the internal stresses and introduces recovery processes in the

steel without a large decrease in hardness or strength.

To obtain the desired mechanical properties it is necessary to cool steel from the proper

temperature at the proper rates and temper them at the proper temperature and time.

Isothermal transformation diagrams for SAE 1045 steel are shown in Figure 6-4.

Heat Treatment of Steels

Common steels, which are really solid solutions of carbon in iron, are body-centered-cubic.

However, the carbon has a low solubility in bcc iron and precipitates as iron carbide when

steel is cooled from 1600ºF (870ºC). The processes of precipitation can be altered by adjusting

the cooling rate. This changes the distribution and size of the carbide which forms a laminar

structure called pearlite during slow cooling processes.

If a steel is quenched into water or oil from 1600ºF (870ºC) a metastable phase called

martensite forms, which is body-centered-tetragonal. This phase sets up large internal stresses

and prevents carbide from forming. The internal stresses produce a high hardness and

unfortunately, low toughness. After cooling, to restore toughness, steels are tempered by

reheating them to a lower temperature around 800ºF (426ºC) and cooling. The tempering

relieves the internal stresses and also allows some iron carbide to form. It also restores

ductility.

Procedure

You are provided with 6 specimens of SAE 1045 steel for your study. Measure the

hardness of all specimens using the RA scale.

1. Heat four specimens in one furnace at 1600 + 25ºF (870 + 15ºC) for 1/2 hour.

2. Put the other 2 specimens in a separate furnace at the same temperature for 1/2 hour.

3. Remove one specimen from the furnace with 2 specimens and cool it in air on a brick.

4. Turn off the furnace with the one remaining specimen. Allow the sample to remain in

the furnace for one hour. The air-cooled and furnace-cooled specimens can be cooled

in water after one hour. Why? (Answer this in your write up).

5. Remove the four specimens and quickly drop them into water; the transfer should take

less than one second. A little rehearsal could help. Be careful not to touch the

specimens before they are cooled in water.

6. Measure Rockwell hardness of the quenched specimens before the next step.

7. Temper 1 each of the quenched specimens for 30 minutes at 600ºF (315ºC), 800ºF

(430ºC), and 1000ºF (540ºC). After tempering, the specimens can be cooled in water.

8. Measure hardness of all 6 samples using the Brinell (3000 kg) and Rockwell A or C

scales.

Data Analysis

1. If more than one impression is made per sample, average the Brinell diameters for each

specimen.

2. Compute the Brinell hardness numbers and compare with the numbers read from a

conversion chart for Rockwell A or C to Brinell.

3. Graph BHN (x-axis) versus Rockwell Hardness numbers (y-axis).

4. Graph Rockwell A or C hardness vs. tempering temperature (oC).

5. Compute the ultimate tensile strength (psi) of all specimens from the average BHN for

each specimen using:

ult= 500 x B.H.N.

Write Up

Prepare a single memo report in conjunction with experiment #7 (Hardenability of

Steels). The report should combine both experiments in one report. Do not write this up

as a two part report. (The hardness and hardenability concepts from the experiments are

related). Within this report you should discuss the data referenced in the "Data Analysis" as

well as the following:

1. What is the purpose of quenching and tempering steel?

2. Discuss the sources of error for the various hardness testers, the relative ease with which

they may be used, and the comparative consistency of test results.

3. What factors probably contributed to the scatter in the hardness data?

4. Which hardness test appears to be most accurate?

5. Using the inverse lever law, estimate the amount of carbide (Fe3C) present at 1338 oF

(just below the eutectoid temperature) for SAE 1045.

6. What are (or should be) the differences in the microstructure for each heat treatment

process and how do these differences correlate with hardness?

7. Discuss errors in this experiment and their sources.

MSE 227L Name ________________________

Heat Treatment of steel & Hardenability

Poor Fair Average Good Excellent

Memorandum Format Used 1 2 3 4 5

Spelling, grammar & punctuation correct 1 2 3 4 5

Report includes: Poor Fair Average Good Excellent

Discuss why the air-cooled and furnace-cooled specimens

can be quenched in water after one hour. 1 2 3 4 5

Compare Brinell numbers (BHN) found from measured

diameters with a conversion chart for Rockwell A or C

(6 specimens). Go to website or reference book to find

this information; include this data in your tables.

1 2 3 4 5

Include tables (results and data measured) for BHN and

RA. Be sure to include measured values from computer. 1 2 3 4 5

Graph BHN (x-axis) vs. Rockwell A or C (y-axis). 2 4 6 8 10

Graph Rockwell A or C (y-axis) hardness vs. tempering

temp. 2 4 6 8 10

Compute ult for all specimens from the average BHN

for each specimen. 1 2 3 4 5

Discuss the purpose of quenching and tempering steel. 1 2 3 4 5

Discuss the sources of error for the various hardness

testers; compare consistency of test results and accuracy

(Rockwell vs Brinell).

1 2 3 4 5

Discuss factors that probably contributed to the scatter in

the hardness data and errors in the experiment (their

sources)

1 2 3 4 5

Calculate amount of carbide (Fe3C) present at 1338 o F for

SAE 1045. Use the phase diagram included in the lab

description and show calculations.

1 2 3 4 5

Discuss the expected microstructure for each heat

treatment process (specifically for the 6 samples). 1 2 3 4 5

Discuss the correlation between microstructure and

hardness. 1 2 3 4 5

Graph hardness as a function of distance from the

quenched end (show both alloys on the same graph). 3 6 9 12 15

Discuss the effects of alloying on hardenability and the

shift in the TTT curve due to alloying. 1 2 3 4 5

Poor Fair Average Good Excellent

Overall level of effort apparent 1 2 3 4 5

Quality of graphs 1 2 3 4 5

Quality of Abstract 1 2 3 4 5

Quality of work description 1 2 3 4 5

Quality of conclusions 1 2 3 4 5

Glossary of Terms Understanding the following terms will aid in understanding this experiment.

Austenite. Face-centered cubic () phase of iron or steel.

Austenitizing. Temperature where homogeneous austenite can form. Austenitizing is the first step in

most of the heat treatments for steel and cast irons.

Annealing (steel). A heat treatment used to produce a soft, coarse pearlite in a steel by austenitizing,

then furnace cooling.

Bainite. A two-phase micro-constituent, containing a fine needle-like microstructure of ferrite and

cementite that forms in steels that are isothermally transformed at relatively low temperatures.

Body-centered cubic. Common atomic arrangement for metals consisting of eight atoms sitting on

the corners of a cube and a ninth atom at the cubes center.

Cementite. The hard brittle intermetallic compound Fe3C that when properly dispersed provides the

strengthening in steels.

Eutectoid. A three-phase reaction in which one solid phase transforms to two different solid phases.

Face-centered cubic. Common atomic arrangement for metals consisting of eight atoms sitting on

the corners of a cube and six additional atoms sitting in the center of each face of the cube.

Ferrite. Ferrous alloy based on the bcc structure of pure iron at room temperature.

Hypereutectoid. Composition greater than that of the eutectoid.

Hypoeutectoid. Composition less than that of the eutectoid.

Martensite. The metastable iron-carbon solid solution phase with an acicular, or needle like,

microstructure produced by a diffusionless transformation associated with the quenching of austenite.

Normalizing. A simple heat treatment obtained by austenitizing and air cooling to produce a fine

pearlite structure.

Pearlite. A two-phase lamellar micro-constituent, containing ferrite and cementite, that forms in steels

that are cooled in a normal fashion or are isothermally transformed at relatively high temperatures.

Tempered martensite. The mixture of ferrite and cementite formed when martensite is tempered.

Tempering. A low-temperature heat treatment used to reduce the hardness of martensite by permitting

the martensite to begin to decompose to the equilibrium phases.

References

D. Callister Jr, Fundamentals of Materials Science and Engineering, J. Wiley & Sons, NY, 3rd Ed. 2008,

Flinn and Trojan, Engineering Materials and Their Applications, Chapter 6

Deiter, Mechanical Metallurgy

ASM Handbook on Heat Treatment, Vol. 2