Configure chap authentication on s0 0 0

In This Skills Assessment (SA) You Will Create A Small Network. You Must Connect The Network Devices And Configure Those Devices To Support Various WAN Protocols. This Will Require That You Reload The Routers Before Starting Your Configuration Of The Next

Assessment Objectives

Part 1: Initialize Devices (2 points, 5 minutes)

Part 2: Configure Device Basic Settings (8 points, 20 minutes)

Part 3: Configure PPP Connections (7 points, 20 minutes)

Part 4: Configure NAT (4 points, 15 minutes)

Part 5: Monitor the Network (6 points, 15 minutes)

Part 6: Configure Frame Relay (7 points, 20 minutes)

Part 7: Configure a GRE VPN Tunnel (6 points, 20 minutes)

Cisco NetAcad_Header(Vertical)-01

CCNA: Connecting Networks SA Exam

Lab 13 CCNA: Connecting Networks

CSIS 430 – Weeks 1 - 4

Hands-On Skills Assessment

Topology

Topology

Complete the assessment in Packet Tracer and document and fill in the blanks. Submit this file and the pka file in Week 8 Lab 13, Points will not be given for incomplete Steps.

Assessment Objectives

Part 1: Initialize Devices (2 points, 5 minutes)

Part 2: Configure Device Basic Settings (8 points, 20 minutes)

Part 3: Configure PPP Connections (7 points, 20 minutes)

Part 4: Configure NAT (4 points, 15 minutes)

Part 5: Monitor the Network (6 points, 15 minutes)

Part 6: Configure Frame Relay (7 points, 20 minutes)

Part 7: Configure a GRE VPN Tunnel (6 points, 20 minutes)

Scenario

In this Skills Assessment (SA) you will create a small network. You must connect the network devices and configure those devices to support various WAN protocols. This will require that you reload the routers before starting your configuration of the next WAN protocol. The assessment has you save your basic device configurations to flash prior to implementing a WAN protocol to allow you to restore these basic configurations after each reload.

The first WAN protocol you will configure is Point-to-Point Protocol (PPP) with CHAP authentication. You will also configure Network Address Translation (NAT), and network monitoring protocols during this phase of the assessment. After your instructor has signed off on this phase, you will reload the routers and configure Frame Relay. After the Frame Relay part is complete, and has been signed off by your instructor, you will reload the routers and configure a GRE VPN tunnel. Network configurations and connectivity will be verified throughout the assessment by using common CLI commands.

Required Resources

3 Routers (Cisco 1941 with Cisco IOS Release 15.2(4)M3 universal image or comparable)

3 PCs (Windows 7, Vista, or XP with terminal emulation program, such as Tera Term.

Console cable to configure the Cisco IOS devices via the console ports

Ethernet and Serial cables as shown in the topology

Initialize Devices

Total points: 2

Time: 5 minutes

Initialize and reload routers.

Erase the startup configurations and reload the devices.

Task

IOS Command

Points

Erase the startup-config file on all routers.

erase startup-config

(1 point)

Reload all routers.

reload

(1 point)

Points: __________ of 2

Configure Device Basic Settings

Total points: 8

Time: 20 minutes

Configure PCs.

Assign static IPv4 address information (IP address, subnet mask, default gateway) to the three PCs in the topology. Refer to the Topology diagram to obtain the IP address information.

Configuration Item or Task

Specification

Points

Configure static IPv4 address information on PC-A.

IP Address: 192.168.11.3

Subnet Mask: 255.255.255.0

Default Gateway: 192.168.11.1

1

Configure static IPv4 address information on PC-B.

IP Address: 192.168.22.3

Subnet Mask: 255.255.255.0

Default Gateway: 192.168.22.1

Configure static IPv4 address information on PC-C.

IP Address: 1-.10.33.3

Subnet Mask: 255.255.255.0

Default Gateway: 10.10.33.1

Configure R1.

Configuration tasks for R1 include the following:

Configuration Item or Task

Specification

Points

Disable DNS lookup

no ip domain-lookup

2

Router name

hostname R1

Encrypted privileged EXEC password

enable secret class

Console access password

Line console 0

Password cisco

login

Telnet access password

Line vty 0 15

Password cisco

login

Encrypt the plain text passwords

Service password-encryption

MOTD banner

Banner motd #Unauthorized Access is Prohibited!#

Configure G0/0

Interface g0/0

Description Connection to 192.168.11.0 LAN

Ip address 192.168.11.1 255.255.255.0

No shutdown

Configure R2.

Configuration tasks for R2 include the following:

Configuration Item or Task

Specification

Points

Disable DNS lookup

No ip domain-lookup

2

Router name

Hostname R2

Encrypted privileged EXEC password

Enable secret class

Console access password

Line console 0

Password cisco

login

Telnet access password

Line vty 0 15

Password cisco

login

Encrypt the plain text passwords

Service password-encryption

MOTD banner

Banner motd #Unauthorized Access is Prohibited!#

Configure G0/0

Interface g0/0

Description Connection to 192.168.22.0 LAN

Ip address 192.168.22.1 255.255.255.0

No shutdown

Configure R3.

Configuration tasks for R3 include the following:

Configuration Item or Task

Specification

Points

Disable DNS lookup

No ip domain-lookup

2

Router name

Hostname R3

Encrypted privileged EXEC password

Enable secret class

Console access password

Line console 1

Password class

login

Telnet access password

Line vty 0 15

Password cisco

login

Encrypt the plain text passwords

Service password-encryption

MOTD banner

Banner motd #Unauthorized Access is Prohibited!#

Configure G0/0

Interface g0/0

Description Connection to 10.10.33.0 LAN

Ip address 10.10.33.1 255.255.255.0

No shutdown

Save device configurations to Flash.

Use the copy running-config BasicConfig command to save the running configuration to flash on each router. You will need this configuration file later in the assessment to restore the routers back to their basic configuration.

Configuration Item or Task

Specification

Points

Copy the running-config on R1 to flash. Name the file BasicConfig.

R1# copy running-config BasicConfig

1

Copy the running-config on R2 to flash. Name the file BasicConfig.

R2# copy running-config BasicConfig

Copy the running-config on R3 to flash. Name the file BasicConfig.

R3# copy running-config BasicConfig

Points: _________ of 8

Configure PPP Connections

Total points: 7

Time: 20 minutes

PPP

Figure 1: PPP Topology

Use Figure 1 to obtain the IP information needed for this part of the student assessment.

Configure R1.

Configuration tasks for R1 include the following:

Task

Specification

Points

Configure S0/0/0.

Set the description.

Set the Layer 3 IPv4 address. Refer to Figure 1 at the top of Part 3 for IP address information.

Set encapsulation to PPP.

Set the clocking rate to 128000.

Activate the interface.

2

Configure CHAP authentication on S0/0/0.

Create a local database entry for CHAP authentication.

Username: R2

Password: cisco

Set a static default route out S0/0/0.

Configure R2.

Configuration tasks for R2 include the following:

Task

Specification

Points

Configure S0/0/0.

Interface s0/0/0

Description PPP connection t0 R2

Ip address 172.27.12.1 255.255.255.252

Encapsulation ppp

Clock rate 128000

No shutdown

3

Configure CHAP authentication on S0/0/0.

Interface s0/0/0

ppp authentication chap

Create a local database entry for CHAP authentication.

Username R1 password cisco

Configure S0/0/1.

Interface s0/0/0

Description PPP connection t0 R2

Ip address 172.27.12.1 255.255.255.252

Encapsulation ppp

Clock rate 128000

No shutdown

Set a static default route out S0/0/1.

Ip route 0.0.0.0 0.0.0.0 s0/0/1

Set a static route for R1 LAN traffic out S0/0/0.

Ip route 192.168.11.0 255.255.255.0 s0/0/0

Configure R3.

Configuration tasks for R3 include the following:

Task

Specification

Points

Configure S0/0/1.

interface s0/0/1

description PPP connection to ISP

ip address 209.165.200.225 255.255.255.248

encapsulation ppp

clock rate 128000

no shutdown

1

Verify network connectivity.

Verify connectivity using the ping command.

From

Command

To

Expected Results

Points

PC-A

ping

PC-B

Ping should be successful.

1

PC-C

ping

R3 G0/1

Ping should be successful.

PC-C

ping

R2 S0/0/1

Ping should be successful.

PC-A

ping

PC-C

Ping should not be successful.

PC-B

ping

PC-C

Ping should not be successful.

PC-C

ping

PC-B

Ping should not be successful.

Points: _________ of 7

Configure NAT

Total points: 4

Time: 15 minutes

Configure R2.

Configuration tasks for R2 include the following:

Task

Specification

Points

Assign a static NAT to map the inside local IP address for PC-B to a Inside Global address.

Ip nat inside source static 192.168.22.3 209.165.200.226

2

Define an access control list to permit the R1 LAN for dynamic NAT.

access-list 1 permit 192.168.11.0

0.0.0.255

Define the dynamic NAT pool for the R1 LAN.

ip nat pool R1-LAN 209.165.200.227

209.165.200.227 netmask

255.255.255.248

Define the NAT from the inside source to the outside pool. Make sure to allow multiple PCs access to this single Inside Global address.

ip nat inside source list 1 pool R1-LAN overload

Define an access control list to permit the R2 LAN for dynamic NAT.

access-list 2 permit 192.168.22.0

0.0.0.255

Define the dynamic NAT pool for the R2 LAN.

ip nat pool R2-LAN 209.165.200.228

209.165.200.228 netmask

255.255.255.248

Define the NAT from the inside source to the outside pool. Make sure to allow multiple PCs access to this single Inside Global address.

ip nat inside source list 2 pool R2-LAN overload

Assign the outside NAT interface.

interface s0/0/1

ip nat outside

Assign the inside NAT interface for the R1 LAN.

interface s0/0/0

ip nat inside

Assign the inside NAT interface for the R2 LAN.

interface g0/0

ip nat inside

Verify network connectivity.

Verify connectivity using the ping command.

From

Command

To

Expected Results

Points

PC-A

ping

PC-C

Ping should be successful.

1

PC-C

ping

Inside Global address for PC-B (209.165.200.226).

Ping should be successful.

Note: It may be necessary to disable the PC firewall for pings to be successful.

Verify NAT Configuration on R2.

Enter the appropriate CLI command needed to display the following:

Command Description

Student Input (command)

Points

Display configured access lists.

show access-lists

1

Display the current active NAT translations.

show ip nat translations

Display detailed information about NAT including interface, access list, and pool assignments.

show ip nat statistics

Points: _________ of 14

Monitor the Network

Total points: 6

Time: 15 minutes

Configure NTP.

Configuration tasks include the following:

Task

Specification

Points

Set the clock on R2 to a date and time specified for NTP testing.

clock set 9:00:00 25 August 2013

1

Configure R2 as the NTP Master.

ntp master 5

Configure R1 so that it uses R2 as its NTP Server.

ntp server 172.27.12.2

Configure Syslog messaging.

Configuration tasks include the following:

Task

Specification

Points

Enable the timestamp service on R1 and R2 for system logging purposes.

service timestamps log datetime msec

1

Enable logging of messages on R1 and R2.

logging host 192.168.11.3

Change message trapping level on R1 and R2.

logging trap debugging

Configure SNMP on R1.

Configuration tasks include the following:

Task

Specification

Points

Create a standard access list to permit the SNMP management station (PC-A) to retrieve SNMP information from R1.

ip access-list standard SNMP-ACCESS permit 192.168.11.3

2

Enable SNMP community access to the SNMP-ACCESS access list.

snmp-server community SA-LAB ro

SNMP-ACCESS

Set the SNMP notification host.

snmp-server host 192.168.11.3 version 2c SA-LAB

Enable all SNMP traps.

snmp-server enable traps

Collect NetFlow data on R2.

Configuration tasks include the following:

Task

Specification

Points

Configure NetFlow data capture on both serial interfaces. Capture ingress and egress data packets.

interface s0/0/0

ip flow ingress

ip flow egress

interface s0/0/1

ip flow ingress

ip flow egress

1

Configure NetFlow data export.

ip flow-export destination 192.168.22.3 9996

Configure the NetFlow export version.

ip flow-export version 9

Verify monitoring configurations.

Enter the appropriate CLI command needed to display the following:

Command Description

Student Input (command)

Points

Display the date and time.

show clock

1

Display the contents of logging buffers.

show logging

Display information about the SNMP communities.

show snmp community

Display the protocol using the highest volume of traffic.

show ip cache flow

Points: _________ of 6

Configure Frame Relay

Total points: 7

Time: 20 minutes

FrameRelay

Figure 2: Frame Relay Topology

Use Figure 2 to obtain the IP information needed for this part of the student assessment.

Reload routers and restore the BasicConfig to memory.

Erase the startup configurations and reload the devices.

For each router, issue the copy flash:BasicConfig running-config command to reload the basic configuration that you saved at the end of Part 2.

Issue the no shutdown command for the G0/0 interface on R1 and R3.

Configure R2 as a Frame Relay Switch.

Copy and paste the following configuration lines into R2. This will configure R2 as a Frame Relay switch and allow you to complete Part 6.

frame-relay switching

int s0/0/0

encapsulation frame-relay

frame-relay intf-type dce

frame-relay route 123 interface s0/0/1 321

frame-relay lmi-type ansi

no shutdown

int s0/0/1

clock rate 128000

encapsulation frame-relay ietf

frame-relay intf-type dce

frame-relay route 321 interface s0/0/0 123

no shutdown

Configure R1.

Configure Frame Relay on S0/0/0 on R1. Configuration tasks for R1 include the following:

Task

Specification

Points

Configure S0/0/0.

interface s0/0/0

description Frame Relay connection to

R3.

ip address 172.27.13.1 255.255.255.252

encapsulation frame-relay

clock rate 128000

no shutdown

2

Disable Inverse ARP on S0/0/0.

no frame-relay inverse-arp

Map the IP local address to the DLCI.

frame-relay map ip 172.27.13.1 123.

Map the remote IP address to the DLCI. Allow for multicast or broadcast traffic.

frame-relay map ip 172.27.13.2 123

broadcast

Change the LMI type to the ANSI standard.

frame-relay lmi-type ansi

Activate the interface.

no shutdown

Create a default route to the IP address on the other side of the Frame Relay link.

ip route 0.0.0.0 0.0.0.0 172.27.13.2

Configure R3.

Configure Frame Relay on a subinterface of S0/0/1 on R3. Configuration tasks for R3 include the following:

Task

Specification

Points

Configure S0/0/1.

interface s0/0/1

encapsulation frame-relay ietf

no shutdown

2

Create a point-to-point subinterface on S0/0/1.

interface s0/0/1.321 point-to-point

description Frame Relay connection to R1

Set the Layer 3 IPv4 address on the subinterface.

ip address 172.27.13.2 255.255.255.252

Disable Inverse ARP on the subinterface.

no frame-relay inverse-arp

Map the subinterface to the DLCI.

frame-relay interface-dlci 321

Create a default route to the IP address on the other side of the Frame Relay link.

ip route 0.0.0.0 0.0.0.0 172.27.13.1

Verify network connectivity.

Verify connectivity using the ping command.

From

Command

To

Expected Results

Points

PC-A

ping

Default gateway

Ping should be successful.

2

PC-C

ping

Default gateway

Ping should be successful.

PC-A

ping

172.27.13.2

Ping should be successful.

PC-C

ping

172.27.13.1

Ping should be successful.

PC-A

ping

PC-C

Ping should be successful.

Note: It may be necessary to disable the PC firewall for pings to be successful.

Verify Frame Relay configuration.

Enter the appropriate CLI command needed to display the following:

Command Description

Student Input (command)

Points

Display Frame Relay LMI statistics.

show frame-relay lmi

1

Display the input and output packet count totals on a Frame Relay permanent virtual circuit (PVC).

Show frame-relay pvc

Display the Frame Relay maps between DLCIs and IP addresses.

show frame-relay map

Points: _________ of 7

Configure a GRE VPN Tunnel

Total points: 6

Time: 20 minutes

GREtunnel

Figure 3: GRE VPN Topology

Use Figure 3 to obtain the IP information needed for this part of the student assessment.

Reload routers and restore the BasicConfig to memory.

Erase the startup configurations and reload the devices.

For each router, issue the copy flash:BasicConfig running-config command to reload the basic configuration that you saved at the end of Part 2.

Issue the no shutdown command for the G0/0 interface on R1 and R3.

Configure Serial Interfaces.

Configuration tasks for R1 include the following:

Task

Specification

Points

Configure S0/0/0.

interface s0/0/0

description HDLC connection to ISP

ip address 172.27.12.1 255.255.255.252

encapsulation hdlc

clock rate 128000

no shutdown

.5

Configuration tasks for R2 include the following:

Task

Specification

Points

Configure S0/0/0.

interface s0/0/0

description HDLC connection to R1

ip address 172.27.12.2 255.255.255.252

encapsulation hdlc

no shutdown

1

Configure S0/0/1.

interface s0/0/1

description HDLC connection to R3.

ip address 172.27.23.2 255.255.255.252

encapsulation hdlc

clock rate 128000

no shutdown

Configuration tasks for R3 include the following:

Task

Specification

Points

Configure S0/0/1.

interface s0/0/1

description HDLC connection to ISP.

ip address 172.27.23.1 255.255.255.252

encapsulation hdlc

no shutdown

.5

Configure the GRE VPN tunnel and EIGRP on R1.

Configuration tasks for R1 include the following:

Task

Specification

Points

Create a GRE tunnel interface.

interface tunnel 0

description GRE VPN tunnel to R3

ip address 172.27.13.1 255.255.255.252

1

Use S0/0/0 as the tunnel source.

tunnel source s0/0/0

Set the tunnel destination with the IP address of the R3 S0/0/1 interface.

tunnel destination 172.27.23.1

Create a default route out S0/0/0.

ip route 0.0.0.0 0.0.0.0 s0/0/0

Configure EIGRP on R1

router eigrp 1

Advertise the LAN and Tunnel subnets in EIGRP. Set the LAN interface to passive.

network 192.168.11.0 0.0.0.255

network 172.27.13.0 0.0.0.3

passive-interface g0/0.

Configure the GRE VPN tunnel and EIGRP on R3.

Configuration tasks for R3 include the following:

Task

Specification

Points

Create a GRE tunnel interface.

interface tunnel 0

description GRE VPN tunnel to R1

ip address 172.27.13.2 255.255.255.252

1

Use S0/0/1 as the tunnel source.

tunnel source s0/0/1

Set the tunnel destination with the IP address of the R1 S0/0/0 interface.

tunnel destination 172.27.12.1

Create a default route out S0/0/1.

ip route 0.0.0.0 0.0.0.0 s0/0/1

Configure EIGRP on R3

router eigrp 1

Advertise the LAN and Tunnel subnets in EIGRP. Set the LAN interface to passive.

network 10.10.33.0 0.0.0.255

network 172.27.13.0 0.0.0.3

passive-interface g0/0.

Verify network connectivity.

Verify connectivity using the following commands.

From

Command

To

Expected Results

Points

PC-A

ping

Default gateway

Ping should be successful.

1.5

PC-C

ping

Default gateway

Ping should be successful.

PC-A

ping

PC-C

Ping should be successful.

R1

traceroute

172.27.23.1

R2 should show up in the traceroute.

R1

traceroute

172.27.13.2

R2 should be absent from traceroute.

Note: It may be necessary to disable the PC firewall for pings to be successful.

Verify GRE VPN configuration.

Enter the appropriate CLI command needed to display the following:

Command Description

Student Input (command)

Points

Display detail information about the GRE tunnel interface.

show interfaces tunnel 0

.5

Points: _________ of 6

.

Router Interface Summary Table

Router Interface Summary

Router Model

Ethernet Interface #1

Ethernet Interface #2

Serial Interface #1

Serial Interface #2

1800

Fast Ethernet 0/0 (F0/0)

Fast Ethernet 0/1 (F0/1)

Serial 0/0/0 (S0/0/0)

Serial 0/0/1 (S0/0/1)

1900

Gigabit Ethernet 0/0 (G0/0)

Gigabit Ethernet 0/1 (G0/1)

Serial 0/0/0 (S0/0/0)

Serial 0/0/1 (S0/0/1)

2801

Fast Ethernet 0/0 (F0/0)

Fast Ethernet 0/1 (F0/1)

Serial 0/1/0 (S0/1/0)

Serial 0/1/1 (S0/1/1)

2811

Fast Ethernet 0/0 (F0/0)

Fast Ethernet 0/1 (F0/1)

Serial 0/0/0 (S0/0/0)

Serial 0/0/1 (S0/0/1)

2900

Gigabit Ethernet 0/0 (G0/0)

Gigabit Ethernet 0/1 (G0/1)

Serial 0/0/0 (S0/0/0)

Serial 0/0/1 (S0/0/1)

Note: To find out how the router is configured, look at the interfaces to identify the type of router and how many interfaces the router has. There is no way to effectively list all the combinations of configurations for each router class. This table includes identifiers for the possible combinations of Ethernet and Serial interfaces in the device. The table does not include any other type of interface, even though a specific router may contain one. An example of this might be an ISDN BRI interface. The string in parenthesis is the legal abbreviation that can be used in Cisco IOS commands to represent the interface.