Galvanic cell experiment errors

Objective:

The purpose of this experiment is to create and experiment galvanic cell and collect/interpret data by using a multimeter to describe the flow of electrons. The we g=had to determine how it is calculated by using the formulas given.

Procedure:

Exercise 1: Construction of a Galvanic Cell

1. Gather all of the supplies listed in the materials list. 2. Use the scissors to cut a strip of the filter paper approximately 1.5 inches in width (1/4 the size of the sheet of filter paper). 3. Cut a strip of filter paper and fold the strip of filter paper in half (widthwise) and then in half again. 4. Folding the filter paper in half and then in half again and put on the safety gloves and goggles. 5. Create the salt bridge by carefully winding the folded filter paper into a circle so that it fits into the bottom of the 9 oz. plastic cup. Add the potassium chloride to the cup with the filter paper until the paper is completely covered with the potassium chloride. 6. Folded filter paper in cup. The potassium chloride is added to the cup to cover the filter paper. 7. Allow the paper to soak up the potassium chloride for a minimum of 10 minutes or until you are ready to add it to the galvanic cell, as described later in the experiment. 8. Place the 2 glass beakers on a table. Add approximately 45 ml of zinc sulfate (approximately ½ of the bottle) to one of the beakers. To the second beaker, add approximately 45 ml of copper sulfate. 9. Pick up a fresh strip of zinc and insert 1 end of it into the copper sulfate solution. After approximately 5 seconds, remove the zinc from the copper sulfate and place it on a piece of paper towel.10. Pick up a fresh strip of copper and insert 1 end of it into the zinc sulfate solution. After approximately 5 seconds, remove the copper from the zinc sulfate and place it on the piece of paper towel.11. Metal in solutions. A. Zinc being inserted into copper sulfate. B. Copper being inserted into zinc sulfate and observe the 2 metal strips and record observations in Data Table 1 in your Lab Report Assistant. 12. From the observations, determine which of the 2 reactions is spontaneous. Record this in the observations section of Data Table 1. 13. Set up the voltmeter as follows; a. Make sure the on/off switch of the voltmeter is in the "off" position. b. Place the end of the black probe into the bottom right hole of the voltmeter. c. Place the end of the red probe into the hole directly above the location of the black probe. d. Turn the voltage dial so that the arrow end of the dial is pointing to 20 DCV. e. Add 1 jumper cable clip to each end of the probes. It does not matter what color jumper cable clips are provided in your kit, or which color is attached to either probe. 14. Put the salt bridge into place by submerging 1 end on the copper sulfate and the other end in the zinc sulfate. Adjust the beakers as necessary so that the salt bridge does not sink between the beakers. 15. Clip a fresh piece of zinc onto 1 of the jumper cable clips and clip a fresh piece of copper onto the other jumper cable clip. 16. Place the zinc into the zinc sulfate solution, so that the metal is submerged in the solution, but the jumper cable clip is above, and not touching, the solution or salt bridge. 17. Place the copper into the copper sulfate solution, so that the metal is submerged in the solution, but the jumper cable clip is above, and not touching the solution or salt bridge. Note: It may take a few minutes to find the correct placement of the copper and zinc into the solutions to keep the jumper cable clip above the solution. Adjust the jumper cable clips as necessary to find the correct placement. 18. Turn the voltmeter on, and observe whether the total voltage is positive or negative. If the voltage reads positive, the galvanic cell was prepared correctly and can be allowed to progress. If the voltage is negative, quickly turn off the voltmeter and swap the jumper cable clips from one metal to the other. 19. When the metals and jumper cable clips are arranged so that the voltmeter has a positive reading, allow approximately 5 minutes for the voltmeter reading to stabilize. When the voltmeter reading has stabilized record the voltmeter reading in Data Table 2 in your Lab Report Assistant, under 0 minutes. 20. look at a clock or watch and record the voltmeter reading for the galvanic cell every 15 minutes for 2.5 hours. 21. While the reaction in the galvanic cell is progressing, use Table 1 in the Background section to determine the 2 half-reactions and standard reduction potentials for the redox reaction