Loading...

Messages

Proposals

Stuck in your homework and missing deadline? Get urgent help in $10/Page with 24 hours deadline

Get Urgent Writing Help In Your Essays, Assignments, Homeworks, Dissertation, Thesis Or Coursework & Achieve A+ Grades.

Privacy Guaranteed - 100% Plagiarism Free Writing - Free Turnitin Report - Professional And Experienced Writers - 24/7 Online Support

Half wave and full wave rectifier lab report

15/10/2021 Client: muhammad11 Deadline: 2 Day

Lab Homework Half-Wave And Full-Wave Rectifier..

Please review the following videos before getting started with this lab:

Watch the video: “Video 3: Basic Electrical Components”
Watch the video: “Video 4: Fundamentals of breadboard”
Watch the video: “Video 5: Simple resistive circuit with NI myDAQ”
Materials and Equipment:

Materials:

Simulated Parts (Multisim):
30/3 Vrms center-tapped transformer
Two diodes 1N4001
Two 2.2 kΩ resistors
One 100 μF, 50 V electrolytic capacitor
One fuse (any rating is fine since it is for simulation only)
Hardware Parts (In the Toolbox):
Two diodes 1N4001
Two 2.2 kΩ resistors
One 100 μF, 50 V electrolytic capacitor
Equipment:

Virtual Instruments (Multisim):
Agilent Function Generator
Tektronix oscilloscope
Hardware Equipment:
Breadboard
NI myDAQ Instrument Device
Screw Driver
Screw Terminal connector
Jumper wires
Oscilloscope and Function generator from NI ELVISmx Intrument Launcher
Procedure:

***** This lab has to be implemented in both software (running simulations on Multisim) and hardware (using NI myDAQ) *****

Part A: Half wave rectification:

figure 1

Figure 1

Software (Multisim):

Construct the circuit of a half-wave rectifier in Figure 1 in Multisim. Use a function generator to provide the AC input of Vacand use a center tapped transformer to obtain VSEC. Be sure to set the tolerance of the resistor to 20%.
Connect the Tektronix oscilloscope so that channel 1 is across the transformer and channel 2 is across the load resistor (RL). Observe the waveforms VSEC and VLOAD.
The output isn’t very useful as a dc source because of the variations in the output waveform. Connect a 100 μF capacitor (C1) with a tolerance of 20% in parallel with the load resistor (RL). (Note the polarity of the capacitor).
Measure the dc load voltage, VLOAD, and the peak-to-peak ripple voltage, VRIPPLE, of the output. Measure the ripple frequency. Tabulate all data gathered and compare the results with and without the filter capacitor.
Hardware (NI myDAQ):

Using the voltage VSEC obtained from the simulation, build the circuit in Figure 1 on the breadboard with VSEC as an input, which connects to the diode and load resistor RL in series. (See Figure 3)
Using the jumper wires, screw driver and screw terminal connector, connect the board to NI MyDAQ Instrument Device to analyze the circuit.
Use channel AO0 on the NI myDAQ Instrument Device to provide the input (VSEC) and channel AI0 to measure the output voltage(VLOAD).
Using the function generator from NI ELVISmx Instrument Launcher, provide the input voltage VSEC to the circuit. Measure the output voltage VLOAD, across the load RL using the oscilloscope.
Repeat steps 3 and 4 with a 100uF capacitor if you notice any variations in the output.
figure 2

Figure 2

Review questions:

What is the purpose of having a half-wave rectifier in the circuit?
Describe the procedure in this lab to arrive at the final design of both the hardware portion and the software portion to achieve the design objectives?
Discuss the impact of having the capacitor on the output voltage and the effect of additional load on the ripple voltage.
Deliverables:

Measured voltage VSEC, the output peak voltage, VLOAD and ripple voltage VRIPPLE. Capture screenshots of your measurements from Multisim.
Place your student ID card on the breadboard and take a picture of the circuit board and pin out on the NI myDAQ device.
Take screenshots of the measurements obtained from function generator and oscilloscope on the NI ELVISmx Instrument Launcher on your screen.
Part B: Full wave rectification:

Software (Multisim):

Construct the circuit of a half-wave rectifier in Figure 3 in Multisim. Use a function generator to provide the AC input of Vacand use a center tapped transformer to obtain VSEC. Notice that the ground for the circuit has changed. Check your circuit carefully before applying power.
Connect the Tektronix oscilloscope so that each channel is across each diode. Observe the waveforms VSEC across each diode and then observe the VLOAD.
Connect a 100 μF capacitor (C1) with a tolerance of 20% in parallel with the load resistor (RL). (Note the polarity of the capacitor).
Measure the dc load voltage, VLOAD, and the peak-to-peak ripple voltage, VRIPPLE, of the output. Measure the ripple frequency. Tabulate all data gathered and compare the results with and without the filter capacitor.
figure 3

Figure 3

Hardware (NI myDAQ):

Using twice the voltage VSEC obtained from the simulation, build the circuit in Figure 3 on the breadboard with 2*VSEC as an input, which connects to the two diodes and load resistor RL in series. (See Figure 4)
Using the jumper wires, screw driver and screw terminal connector, connect the board to NI MyDAQ Instrument Device to analyze the circuit.
Use channel AO0 on the NI myDAQ Instrument Device to provide the input (2*VSEC) and channel AI0 to measure the output voltage (VLOAD).
Using the function generator from NI ELVISmx Instrument Launcher, provide the input voltage VSEC to the circuit. Measure the output voltage VLOAD, across the load RL using the oscilloscope.
Repeat steps 3 and 4 with a 100uF capacitor if you notice any variations in the output.
figure 4

Figure 4

Review questions:

What is the purpose of having a full-wave rectifier in the circuit?
Describe the procedure in this lab to arrive at the final design of both the hardware portion and the software portion to achieve the design objectives?
Discuss the impact of having the capacitor on the output voltage and the effect of additional load on the ripple voltage.
How is the output of the full-wave rectifier different from half-wave rectifier?
Deliverables:

Measured voltage VSEC, the output peak voltage, VLOAD and ripple voltage VRIPPLE. Capture screenshots of your measurements from Multisim.
Place your student ID card on the breadboard and take a picture of the circuit board and pin out on the NI myDAQ device.
Capture screenshots of your measurements from the NI ELVISmx Instrument Launcher showing both the input from the function generator and output on the oscilloscope on your screen.
Lab Report:

Use the Lab report template found in the “Tools and Template” link in the navigation center.
Include all the deliverables from Part A and Part B.
Include all the screenshots of the measurements from Multisim, circuit design on the breadboard using NI myDAQ device and measurements from MI ELVISmx Instrument Launcher.
Save the document as Lab2YourGID.docx (ex: Lab2G00050331.docx) and submit in Blackboard.
Grading Rubrics

Grading CriteriaPointsPart A: Half-wave rectifier circuit in Multisim – with and without filter capacitor10Part A: Half-wave rectifier circuit on NI myDAQ and breadboard with and without filter capacitor10Part A: Deliverables: Measurements and screen captures from Multisim and hardware15Review Questions10Part B: Full-wave rectifier circuit in Multisim – with and without filter capacitor10Part B: Full -wave rectifier circuit on NI myDAQ and breadboard with and without filter capacitor10Part B: Deliverables: Measurements and screen captures from Multisim and hardware15Review Questions10Report format (Proper use of template)10TOTAL100

Homework is Completed By:

Writer Writer Name Amount Client Comments & Rating
Instant Homework Helper

ONLINE

Instant Homework Helper

$36

She helped me in last minute in a very reasonable price. She is a lifesaver, I got A+ grade in my homework, I will surely hire her again for my next assignments, Thumbs Up!

Order & Get This Solution Within 3 Hours in $25/Page

Custom Original Solution And Get A+ Grades

  • 100% Plagiarism Free
  • Proper APA/MLA/Harvard Referencing
  • Delivery in 3 Hours After Placing Order
  • Free Turnitin Report
  • Unlimited Revisions
  • Privacy Guaranteed

Order & Get This Solution Within 6 Hours in $20/Page

Custom Original Solution And Get A+ Grades

  • 100% Plagiarism Free
  • Proper APA/MLA/Harvard Referencing
  • Delivery in 6 Hours After Placing Order
  • Free Turnitin Report
  • Unlimited Revisions
  • Privacy Guaranteed

Order & Get This Solution Within 12 Hours in $15/Page

Custom Original Solution And Get A+ Grades

  • 100% Plagiarism Free
  • Proper APA/MLA/Harvard Referencing
  • Delivery in 12 Hours After Placing Order
  • Free Turnitin Report
  • Unlimited Revisions
  • Privacy Guaranteed

6 writers have sent their proposals to do this homework:

Finance Professor
Professional Accountant
Accounting & Finance Mentor
Essay Writing Help
Smart Homework Helper
Engineering Solutions
Writer Writer Name Offer Chat
Finance Professor

ONLINE

Finance Professor

I have assisted scholars, business persons, startups, entrepreneurs, marketers, managers etc in their, pitches, presentations, market research, business plans etc.

$30 Chat With Writer
Professional Accountant

ONLINE

Professional Accountant

I reckon that I can perfectly carry this project for you! I am a research writer and have been writing academic papers, business reports, plans, literature review, reports and others for the past 1 decade.

$27 Chat With Writer
Accounting & Finance Mentor

ONLINE

Accounting & Finance Mentor

I have done dissertations, thesis, reports related to these topics, and I cover all the CHAPTERS accordingly and provide proper updates on the project.

$47 Chat With Writer
Essay Writing Help

ONLINE

Essay Writing Help

As per my knowledge I can assist you in writing a perfect Planning, Marketing Research, Business Pitches, Business Proposals, Business Feasibility Reports and Content within your given deadline and budget.

$47 Chat With Writer
Smart Homework Helper

ONLINE

Smart Homework Helper

I can assist you in plagiarism free writing as I have already done several related projects of writing. I have a master qualification with 5 years’ experience in; Essay Writing, Case Study Writing, Report Writing.

$29 Chat With Writer
Engineering Solutions

ONLINE

Engineering Solutions

I have read your project description carefully and you will get plagiarism free writing according to your requirements. Thank You

$15 Chat With Writer

Let our expert academic writers to help you in achieving a+ grades in your homework, assignment, quiz or exam.

Similar Homework Questions

Balby carr community academy - 1870 in roman numerals - Offshore emergency response team member - Preposition song yankee doodle about above across after - Marketing strategy for milk tea business - A cvp graph presents data on - Themes in how to kill a mockingbird - Cbs on virgin media - Southwest airlines in 2014 case study - Keith rn case studies - Lancaster university interactive transcript - Kvar formula 3 phase - Polyvision walk and talk - Forced choice preference assessment - Rough Draft Qualitative Research Critique and Ethical Considerations - Schonell reading test printable - Clinical Supervision - Qualitative analysis of group 4 cations lab report - Kent institute moodle - Kite streamers wang meng summary - Examples of diverging lenses in everyday life - When writing a persuasive claim letter you should - Govc sean brown net worth - Assignment 1 lenscrafters case study - Essay about china culture - Trinny and susannah shapewear debenhams - Stressed and unstressed syllables - Agwa bomb alcohol percentage - Measurement of an equilibrium constant lab report - What gas makes up 78 of the atmosphere - Hattie and the fox pdf - Melbourne city college australia - Country manager simulation how to win - STR/580 wk5 Apply Signature Assignment: Strategic Analysis - 100 spelling words for 5th grade - Nutrition and drugs - Smu information systems management - Harvard global supply chain management simulation v2 solution - Pham yvonne t huyen dr - Badminton skills and techniques - Lab building proteins from rna assignment lab report - The island of sodor - The curious researcher chapter 1 - Presentation nike - Kks power plant classification system pdf - Disgronificator - Walmart case study - The papin sisters youtube - Q link pendant australia - Week 3 Discussion Creativity and Innovation - The moment the gun went off - Return on equity dupont formula - What does chivalry mean today - Cambridge law test model answers - Ld didactic physics leaflets - Reread this sentence from the letter from birmingham jail - Cloud computing intranet - Research paper - Customer buying criteria capsim - Was andrew jackson a great president - Marxist literary criticism ppt - Why do ariel and the other sylphs abandon belinda - Prime value growth fund - Rate constant units for first order reaction - Kerosene safety data sheet - History of America - Catalina meaning in hebrew - T model small signal - Journal 6- Using the Bitcoin Blockchain - Powers powder actuated tool - Signature Assignment: Infrastructure, Best Practices, and Security - Work method statement template free - Is collateral beauty on redbox - Afue vs thermal efficiency - What is first class lever - Life cycle phases in an epm system - Bridge to terabithia drawings - New york slave revolt - 520 paper - Luisa muchas presiones este año - How many orbitals in 4s - Green ninja energy tracker - Incontinency definition hamlet - Fulbright corp uses the periodic inventory system - 300 words - A bat flying in a cave emits a sound - How to calculate gross potential rent - Molar mass of 85 phosphoric acid - Project - Feldman's three-phase model of socialization and the six socialization tactics - English-The Read Aloud - How to calculate cpk in excel - Discussion 9 - Table setting etiquette worksheet - Clairol touch of yogurt shampoo - Presentaion 7 - Week16-Discussion8-Information Technology Importance For Strategic Planning - Importance of psychological test in employee selection - George kyparisis makes bowling balls in his miami plant - South african apartheid secondary sources