Loading...

Messages

Proposals

Stuck in your homework and missing deadline? Get urgent help in $10/Page with 24 hours deadline

Get Urgent Writing Help In Your Essays, Assignments, Homeworks, Dissertation, Thesis Or Coursework & Achieve A+ Grades.

Privacy Guaranteed - 100% Plagiarism Free Writing - Free Turnitin Report - Professional And Experienced Writers - 24/7 Online Support

Rl circuit lab report

16/12/2020 Client: saad24vbs Deadline: 3 days

EET 202


LAB EXPERIMENT INSTRUCTIONS


AC circuit analysis II


Lab # 3


RL Series and Parallel Circuits


Experiment #1: Series RL Circuits


Objectives:


After p11erforming this experiment you will be able to:


1. Compute the inductive reactance of an inductor from voltage measurement in a series RL circuit


2. Draw the impedance and voltage phasor diagram for series RL circuit.


3. Measure the phase angle in a series circuit using either of the two methods.


Materials Needed:


Resistor: 10 KΩ - 1 Piece.


Inductor: 100 mH – 1 Piece.


Summary of Theory:


When a sine wave drives a linear series circuit, the phase relationship between the current and the voltage are determined by the components in the circuit. The current and voltage are always in phase across resistors. With capacitors, the current is always leading the voltage by 90o, but for inductors, the voltage always leads the current by 90o.


Figure 3-1-1(a) illustrates a series RL circuit. The graphical representation of the phasors for this circuit is shown in Figure 3-1-1(b) and (c) respectively. As in the series RC circuit, the total impedance is obtained by adding the resistance and inductive reactance using the algebra for complex numbers. In this example, the current is 1.0 mA, and the total impedance is 5 KΩ. The current is the same in all components of a series circuit, so the current is drawn as a reference in the direction of the x-axis. If the current is multiplied by the impedance phasors, the voltage phasors are obtained and shown in Figure 3-1-(c).


image25.png


Figure 3-1-1 (a)


Procedure:


In this experiment, you learn how to make measurement of the phases angle. Actual inductors may have enough resistance to affect the phase angle in the circuit. You will use a series resistor that is large compared to the inductor’s resistance to avoid this error.


1. Measure the actual resistance of a 10 KΩ resistor and the inductance of a 100 mH inductor. If the inductor cannot be measured, record the listed value. Record the measured values in Table 3-1-1.


2. Connect the circuit shown in Fig 3-1-2. Set the generator voltage with the circuit connected to 3.0 VPP at a frequency of 25 KHz. The generator should have no dc offset. Measure the generator voltage and frequency with oscilloscope as many meters cannot respond to 25 KHz frequency. Use peak-to-peak readings for all the voltage and current measurements in this experiment.


image1.png


Figure 3-1-1 (b)


image24.png


Figure 3-1-1 (c)


Component


Listed Value


Measured Value


L1


100 mH


R1


10 KΩ


Table 3-1-1


image2.png


Figure 3-1-2


3. Using a two-channel oscilloscope, measure the peak-to-peak voltage across the resistor (VR) and the peak-to-peak voltage across the inductor (VL)


(see Fig. 3-1-3). Measure the voltage across the inductor using the difference technique described in experiment #2 of the Lab # 1. Record the voltage reading in Table 3-1-2.


VR


VL


I


XL


ZT


Table 3-1-2


4. Compute the peak-to-peak current in the circuit by applying Ohm’s Law to the resistor. That is


image3.wmf

R


V


I


R


=


Enter the computed current in Table 3-1-2.


5. Compute the inductive reactance, XL by applying Ohm’s Law to the inductor. The reactance is


image4.wmf

L


L


V


X


I


=


Enter Computed reactance in Table 3-1-2.

6. Calculate the total impedance (ZT) by applying Ohm’s Law to the entire circuit. Use the generator voltage set in step 2 (VS) and the current determined in step 4. Enter the computed impedance in Table 3-1-2.


7. Using the values listed in Table 3-1-1 and 3-1-2 draw the impedance phasors on the Plot 3-1-1(a) and the voltage phasors on the Plot 3-1-1(b) for the circuit at a frequency of 25 KHz.


image5.png


Plot 3-1-1


8. Compute the phase angle between VR and VS using trigonometric relation.


image6.wmf

1


L


R


V


Tan


V


q


-


æö


=


ç÷


èø


Enter the computed phase angle in Table 3-1-3.

9. Two methods for measuring phase angle will be used. The first method can be used with any oscilloscope. The second can only be used with oscilloscopes that have a “fine” or variable SEC/DIV control. Measure the phase angle between VR and VS using one or both methods. The measured phase angle will be recorded in Table 3-1-3.


Phase Angle Measurement: Method #1:


a) Connect the oscilloscope so that the channel 1 is across the generator and channel 2 is across the resistor. [See Fig 3-1-3]. Obtain a stable display showing between one and two cycles while viewing channel 1 (VS). The scope should be triggered from channel 1.


b) Measure the period T of the signal from the generator. Record it in Table 3-1-3. You will use this time, T, in step (e).


image7.png


Figure 3-1-3


c) Set the oscilloscope to view both channels. Do not have channel 2 inverted. Adjust the amplitude of the signals using the VOLTS/DIV, VERT POSITION, and vernier controls until both channels appear to have the same amplitude as seen on the scope face.


d) Spread the signal horizontally using the SEC/DIV control until both signals are just visible across the screen. The SEC/DIV control must remain calibrated. Measure the time between the two signals,


image8.wmf

t


D


, by counting the number of divisions along a horizontal graticule of the oscilloscope and multiplying the SEC/DIV setting. (See Fig. 3-1-4). Record the measured

image9.wmf

t


D


in Table 3-1-3.

e) The phase angle may now be computed from the equation.


image10.wmf

360


t


T


q


D


æö


=´°


ç÷


èø


Enter the measured phase angle in Table 3-1-3 under the phase angle – method 1.


Computed Phase Angle


image11.wmf

q


Measured Period


image12.wmf

T


Time Difference


image13.wmf

t


D


Phase Angle


Method 1


image14.wmf

q


Method 2


image15.wmf

q


Table 3-1-3


image16.png


Figure 3-1-4


Phase Angle Measurement – Method #2:


a) In this method the oscilloscope face will represent degrees, and the phase angle can be measured directly. The probes are connected as before. View channel 1 and obtain a stable display. Then adjust the SEC/DIV control and its vernier until you have exactly one cycle across the scope face. This is equivalent to 360o in 10 divisions, so each division is worth 36o.


b) Now switch the scope to view both channels. As before, adjust the amplitude of the signals using the VOLTS/DIV, VERT POSITION and vernier control until both channels appear to have the same amplitude.


c) Measure the number of divisions between the signals and multiply by 36o per division. Record the measured phase angle in Table 3-1-3 under phase angle-method 2.


Experiment #2: Parallel RL circuits:


Objectives:


After performing this experiment, you will be able to:


1. Determine the current phasor diagram for a parallel RL circuit.


2. Measure the phase angle between the current voltage for a parallel RL circuit.


3. Explain how an actual circuit differs from the ideal model of a circuit.


Materials Needed:


Resistors: 3.3 KΩ - 1 Piece, 47Ω - 2 Pieces.


Inductor: 100 mH – 1 Piece.


Summary of Theory:


In a parallel RL circuit, the current phasors will be drawn with reference to the voltage phasor. The direction of the current phasor in a resistor is always in direction of the voltage. Since current lags the voltage in an inductor, the current phasor is drawn at an angle of – 90o from the voltage reference. A parallel RL circuit and the associated phasors are shown in Figure 3-2-1.


image17.jpg


Figure 3-2-1


The practical inductors contain resistance that frequently is large enough to affect the purely reactive inductor phasor drawn in Figure 3-2-1. The resistance of an inductor can be thought of as a resistor in series with a pure inductor. The effect on the phasor diagram is to reduce an angle between IL and IR. In a practical circuit, this angle will be slightly less than the -90o shown in the Figure 3-2-1. This experiment illustrates the difference between the approximations of circuit performance based on ideal components and the actual measured values.


Recalling the previous experiment – RL series circuit, the phase angle between the source voltage, VS, and the resistor voltage, VR in a series circuit were measured. The oscilloscope is a voltage-sensitive device, so comparing these voltages is straightforward. In parallel circuits, the phase angle of interest is usually between the total current, IT, and one of the branch currents. To use the oscilloscope to measure the phase angle in a parallel circuit, we must convert the current to a voltage. This was done by inserting a small resistor in the branch where the current is to be measured. The resistor must be small enough not to have a major effect on the circuit.


Procedure:


1. Measure the actual resistance of a resistor with a color-code value of 3.3 KΩ and resistance of two current-sensing resistors of 47Ω each. Measure the inductance of a 100 mH inductor. Use the listed value if you cannot measure the inductor. Record the measured values in Table 3-2-1.


2. Measure the winding resistance of the inductor, RW , with an ohmmeter. Record the resistance in Table 3-2-1.


3. Construct the circuit shown in Figure 3-2-2. Notice that the reference ground connection is at the low side of the generator. This connection will enable you to use a generator that does not have a “floating” common connection. Using your oscilloscope, set the generator to a voltage of 6.0 VPP at 5 KHZ. Check both the voltage and frequency with your oscilloscope. Record all voltages and currents in this experiment as peak-to-peak values.


image18.png


Table 3-2-1


image19.png


Figure 3-2-2


4. Using the oscilloscope, measure the peak-to-peak voltages across R1, RS1 and RS2. Use the two channel difference method (described in Lab#1) to measure the voltage across the two ungrounded resistors. Apply Ohm’s Law to Compute the Current in each branch. Record the measured voltage drops and the computed currents in Table 3-2-1. Since L1 is in series with RS2, enter the same current for both.


5. Using the computed peak-to-peak currents from Table 3-2-1, draw the current phasors for the circuit on the Plot 3-2-1. [Ignore the effects of the sense resistors].


image20.png


Plot 3-2-1.


image21.wmf

1


L


R


I


Tan


I


q


-


æö


ç÷


ç÷


èø


=


Phase Angle


Between


Computed


Measured


IT and IR




IR and IL


90o



IT and IL




Table 3-2-2


6. The phasor diagram illustrates the relationship between the total current and the current in each branch. Using the measured currents, compute the phase angle between the total current (IT) and the current in R1 (IR). Then compute the phase angle between the total current (IT) and the current in L1 (IL). Enter the computed phase angles in Table 3-2-2 (Note that the computed angles should add up to 90o, the angle between IR and IL.


7. In this step, you will measure the phase angle between the generator voltage and current. This angle is approximately equal to the angle between IT and IR as show in Figure 3-2-1. (Why?). Connect the oscilloscope probes as shown in Figure 3-2-3. Measure the phase angle using one of the methods in the previous experiment. The signal amplitudes in each channel are quite different, so the vertical sensitivity controls should be adjusted to make each signal appear to have the same amplitude on the scope. Record the measured angle between IT and IR in Table 3-2-2.


image22.jpg


Figure 3-2-3


8. Replace RS1 with jumper. This procedure enables you to the reference the low side of R1 and RS2. Measure the angle between IL and IR by connecting the probes as shown in Fig 3-2-4. Ideally this measurement should be 90o, but because of the coil resistance, you will likely find a smaller value. Adjust both channels for the same apparent amplitude on the scope face. Record your measured result in the second line in the Table 3-2-2.


image23.png


Figure 3-2-4


9. By subtracting the angle measured in step 7 from the angle measured step 8, you can find the phase angle between IT and IL. Record this as the measured value on the third line of the Table 3-2-2.


Page 1 of 12


_1182578268.unknown

_1182578269.unknown

_1182578270.unknown

_1182620091.unknown

_1182620114.unknown

_1221974526.unknown

_1182578267.unknown

_1182578259.unknown

_1182576491.unknown

_1182576135.unknown

_1182575957.unknown

_1182575754.unknown

Applied Sciences

Architecture and Design

Biology

Business & Finance

Chemistry

Computer Science

Geography

Geology

Education

Engineering

English

Environmental science

Spanish

Government

History

Human Resource Management

Information Systems

Law

Literature

Mathematics

Nursing

Physics

Political Science

Psychology

Reading

Science

Social Science

Home

Blog

Archive

Contact

google+twitterfacebook

Copyright © 2019 HomeworkMarket.com

Homework is Completed By:

Writer Writer Name Amount Client Comments & Rating
Instant Homework Helper

ONLINE

Instant Homework Helper

$36

She helped me in last minute in a very reasonable price. She is a lifesaver, I got A+ grade in my homework, I will surely hire her again for my next assignments, Thumbs Up!

Order & Get This Solution Within 3 Hours in $25/Page

Custom Original Solution And Get A+ Grades

  • 100% Plagiarism Free
  • Proper APA/MLA/Harvard Referencing
  • Delivery in 3 Hours After Placing Order
  • Free Turnitin Report
  • Unlimited Revisions
  • Privacy Guaranteed

Order & Get This Solution Within 6 Hours in $20/Page

Custom Original Solution And Get A+ Grades

  • 100% Plagiarism Free
  • Proper APA/MLA/Harvard Referencing
  • Delivery in 6 Hours After Placing Order
  • Free Turnitin Report
  • Unlimited Revisions
  • Privacy Guaranteed

Order & Get This Solution Within 12 Hours in $15/Page

Custom Original Solution And Get A+ Grades

  • 100% Plagiarism Free
  • Proper APA/MLA/Harvard Referencing
  • Delivery in 12 Hours After Placing Order
  • Free Turnitin Report
  • Unlimited Revisions
  • Privacy Guaranteed

6 writers have sent their proposals to do this homework:

Homework Guru
University Coursework Help
Helping Hand
Top Essay Tutor
Writer Writer Name Offer Chat
Homework Guru

ONLINE

Homework Guru

Hi dear, I am ready to do your homework in a reasonable price and in a timely manner.

$77 Chat With Writer
University Coursework Help

ONLINE

University Coursework Help

Hi dear, I am ready to do your homework in a reasonable price.

$77 Chat With Writer
Helping Hand

ONLINE

Helping Hand

I am an Academic writer with 10 years of experience. As an Academic writer, my aim is to generate unique content without Plagiarism as per the client’s requirements.

$75 Chat With Writer
Top Essay Tutor

ONLINE

Top Essay Tutor

I have more than 12 years of experience in managing online classes, exams, and quizzes on different websites like; Connect, McGraw-Hill, and Blackboard. I always provide a guarantee to my clients for their grades.

$80 Chat With Writer

Let our expert academic writers to help you in achieving a+ grades in your homework, assignment, quiz or exam.

Similar Homework Questions

Aws certification dumps pdf - Virtual lab mealworm behavior worksheet - Should cost be a factor in carmex prices - 2015 practice test 1 psat nmsqt answers - Maria the boy in the striped pajamas - Cembre narrow palm lugs - Frimley park hospital phone number - Grand strategy selection matrix - Scu harvard referencing - Roller coaster polynomials project answers - Bsbwor203 work effectively with others answers - Direct and inverse variation equations - Using sap 2000 - Ansi z535 1 2006 r2011 - As/nzs 2293.2 free download - International Business Communications - Chromogen free hot water system - Schwartz Theory of Basic Values - Management of a surgical unit evolve case study - Business intelligence concepts components techniques and benefits - Tuxedo marlene dietrich suit - History of nurse anesthesia - What you pawn i will redeem annotated bibliography - Epiphany prayer service catholic - Freddie gray family buys lamborghini - Rachel mcdowall street dance - The Health Assessment - Dan murphys james squire - Mdc and ldc countries - Examples of opaque objects - Bonds payable long term liability - Fish creek animal hospital case study - Carlos vega puerto rico - Avocado and artichoke view of human nature - My sister's keeper based on true story - Discussion - 60a cut out fuse - Digital Archive - Computer engineering drafting and design syllabus - Post adjusting entries to the t accounts problem 4 8a - April business simulation - Eng 125 week 3 assignment - Retail and service logistics (COURTS industry research report) - How to write a tv show analysis - Paper 2 - Dry shampoo at dollar general - Highline financial services ltd - Gelatin hydrolysis test e coli - Blue nile case study answers - Transgenerational model of family therapy - Business case study - APA style 6 pages - Health Orga D32 - Future value for single cash flow - Money banking and financial markets edition solutions - Hepa filter test methods - Https statistics laerd com spss tutorials - Posttraumatic Stress Disorder - What breaks pascal's balloon in the book albert - 0.75 kw electric motor - Your bank account pays interest with an ear of 5 - Emotional Contagion Theory - International Business - Marketing plan for Blue Bottle coffee in South Korea - Wk6 DQ1 Discussion Question 1 – CLO 3 - Writing logically thinking critically 6th edition - Two one film review - Carpe diem william shakespeare - Peaceful end of life theory - 18 candles speech sample - Toad brigade to trick track hall - During a fact finding interview an important guideline is - E6 daikin fault code - 2 nuns in a bathtub joke - Alert and oriented x3 but confused - Beth gelert poem summary - MG375 Unit 8 Assignment - Area of a a4 paper - Full tilt character descriptions - Effective communication for colleges 11th edition pdf - Stroke pico question examples - Experiment 1: enzymes in food - CFI3-2 - When was the 300 lb wrestler on television math worksheet - Stan cherelstein - Dc shunt motor circuit diagram - Ethica and Legal Aspects of Nursing Practice DQ 9 student reply Lisney Caraballo - Local Governance Structure - A rectangular sign over a store has a mass - An asset turnover ratio of 1.75 can be interpreted as - Crank and slider vex instructions - 7 page criminal justice research paper due at midnight - Animal farm essay questions pdf - Presentation - Si hoc non legere potes tu asinus es - Personal worldview inventory essay - Boundary value analysis tutorialspoint - Bloomberg bmc questions and answers - High country inc produces and sells many recreational products - English Research and Writing Completion - English Draft template paper