Identifying an unknown hydrogen carbonate lab answers

I’m working on a Chemistry exercise and need support.

- please make sure all answers are correct and clear.

- do your work on paper and send me a picture of it.

- pre-lab questions at the end of the documentCHEM 403 Exp 6 Experiment 6: IDENTIFICATION OF A COMPOUND BY MASS RELATIONSHIPS* In the previous experiment, you learned how to find the formula of a compound by analysis for the elements it contains. When chemical reactions occur, there is a relationship between the masses of the reactants and products that follows directly from the balanced equation for the reaction and the molar masses of the species that are involved. In this experiment, you will use this relationship to identify an unknown substance. Your unknown will be one of the following compounds, all of which are salts: NaHCO3 Na2CO3 KHCO3 K2CO3 In the first part of the experiment, you will be heating a weighed sample of your compound in a crucible. If your sample is a carbonate, there will be no chemical reaction that occurs, but any small amount of adsorbed water will be driven off. If your sample is a hydrogen carbonate, it will decompose by the following reaction, using NaHCO3 as the example: 2NaHCO3(s) → Na2CO3(s) + H2O(g) + CO2(g) (1) In this case, there will be an appreciable decrease in mass, since some of the products will be driven off as gases. If such a mass decrease occurs, you have strong evidence that your sample is a hydrogen carbonate, either NaHCO3 or KHCO3. In the second part of the experiment, you will treat the solid carbonate in the crucible with HCl, hydrochloric acid. There will be considerable effervescence as CO 2 gas is evolved; the reaction that occurs, again using Na2CO3 as our example, is: Na2CO3(s) + 2H+(aq) + 2Cl−(aq) → 2NaCl(s) + H2O(l) + CO2(g) (2) (Since HCl in solution exists as ions, the equation is written in terms of ions.) You will then heat the crucible strongly to drive off any excess HCl and any water that is present, obtaining pure, dry, solid NaCl as your product. To identify your unknown, you will need to find the molar masses of the possible reactants and final products. For each of the possible unknowns there will be a different relationship between the mass of the original sample and the mass of the chloride salt that is produced in Reaction 2. If you know your sample is a carbonate, you need only be concerned with the mass relationships in Reaction 2, and should use as the original mass of your unknown the mass of the carbonate after it has been heated. If you have a hydrogen carbonate, the overall reaction your sample undergoes will be the sum of Reactions 1 and 2. From your experimental data, you will be able to calculate the ratio of the mass of the solid chloride to the mass of either the original hydrogen carbonate or the mass of the anhydrous carbonate in your sample of unknown. From your calculation of the relative masses of solid chloride to solid hydrogen carbonate or solid carbonate in Equations 1 and 2 you can calculate *Adapted from Slowinski, E. J., Wolsey, W. C. Chemical Principles in the Laboratory 9th ed. CHEM 403 Exp 6 what the theoretical ratio of those masses should be. Your observed value should match one of the theoretical values and thus allow you to identify your unknown compound. Procedure Obtain an unknown from the instructor. Weigh a clean, dry crucible, and record its mass. Place approximately 0.5 g of your unknown into the crucible, and record the total mass of the sample with the crucible. Place the crucible on a clay triangle supported by an iron ring. Light your Bunsen burner away from the crucible, and adjust the burner so that you have a small flame. Holding the burner in your hand, gently heat the crucible as you move the burner back and forth. Heat the crucible, gently and intermittently, for a few minutes. Gradually increase the flame intensity, to the point where clay triangle glows red. Heat for 10 minutes. Allow the crucible to cool for 10 minutes, and then weigh it with the sample, recording the mass. At this point, the sample in the crucible is a dry carbonate, since the heating process will convert any hydrogen carbonate to carbonate. Place the crucible back on the clay triangle. Add about 25 drops of 6 M HCl, a drop at a time, to the sample. As you add each drop, you will probably observe effervescence as CO2 is produced. Let the action subside before adding the next drop, to keep the effervescence confined to the lower part of the crucible. You do not want the product to foam up over the edge. When you have added all the HCl, the effervescence should have ceased, and the solid should be completely dissolved. Heat the crucible gently for brief periods to complete the solution process. If all of the solid is not dissolved, add 6 more drops of 6 M HCl and warm gently. Heat the crucible, gently and intermittently, for about 10 minutes, to slowly evaporate the water and excess HCl. If you heat too strongly, spattering will occur and you may lose some sample. When the sample is dry, gradually increase the flame intensity, finally getting the bottom clay triangle to a red heat. Heat at full flame strength for 10 minutes, then allow the crucible to cool for 10 minutes. Weigh it and the contents, recording the mass. CHEM 403 – Exp 6 Name:______________________________ Section: _________ Data & Calculations Unknown # __________ Mass of crucible __________ g Mass of crucible and unknown __________ g Mass of unknown __________ g Mass of crucible and unknown after heating __________ g Loss of mass of sample __________ g Based on the loss of mass, this sample is a: (circle your choice) carbonate hydrogen carbonate Mass of crucible and solid chloride __________ g Mass of solid chloride __________ g Experimental Mass Ratio mass of chloride : mass of hydrogen carbonate (if your sample is a hydrogen carbonate) __________:1 mass of chloride : mass of dry carbonate (if your sample is a carbonate) __________:1 Comparison to Theoretical Mass Ratios (from prelab assignment) If your unknown in a hydrogen carbonate, compare your experimental mass ratio to the two hydrogen carbonate theoretical mass ratios; if your unknown is a carbonate, compare your experimental mass ratio to the two carbonate theoretical mass ratios. Identity of unknown based on match to theoretical mass ratio: _____________ Discuss your results. How well did your experimental mass ratio match one of your theoretical mass ratios? Are you confident in your identification of your unknown?